B&R ID code | 0xE56B |
System requirements | |
Automation Studio | 4.1.4.375 and later |
Automation Runtime | K4.08 and later |
Support for X20SLX modules | Rev. B4 and later |
Cooling | Fanless |
Power button | No |
Reset button | Yes |
Status indicators | Supply voltage OK, operating state, module status, POWERLINK, Ethernet, CAN Rx/Tx, RS232 Rx/Tx |
Buzzer | Yes |
Support | |
Controller redundancy | No |
ACOPOS support | Yes |
Visual Components support | Yes |
Certifications | |
CE | Yes |
UKCA | Yes |
UL | cULus E115267 Industrial control equipment |
Bootloader | Automation Runtime AR 4.08 |
Real-time clock | Nonvolatile, resolution 1 s, -10 to 10 ppm accuracy at 25°C |
FPU | Yes |
Processor | |
Type | Atom E620T |
Clock frequency | 333 MHz (compatible) |
L1 cache | |
Data code | 24 kB |
Program code | 32 kB |
L2 cache | 512 kB |
Mode/Node switches | No |
Remanent variables | 32 kB FRAM, retention >10 years |
DRAM | 256 MB |
Shortest task class cycle time | 0.4 ms |
Typical instruction cycle time | 0.01 µs |
Application memory | |
Type | 2 GB eMMC flash memory |
Data retention | 10 years |
Writable data amount | |
Guaranteed | 40 TB |
Results for 5 years | 21.9 GB/day |
Guaranteed erase/write cycles | 20,000 |
Error-correcting code (ECC) | Yes |
Storage health data support | Yes, starting with AR 4.90 and hardware revision F0 |
Temperature cutoff | Yes, at >88°C |
Type | TFT color |
Diagonal | 7.0″ |
Colors | 16.7 million (RGB, 8 bits per channel) |
Resolution | WVGA, 800 x 480 pixels |
Contrast | Rev. ≥ H3: Typ. 550:1 Rev. < H3: Typ. 600:1 |
Viewing angles | |
Horizontal | Direction L / Direction R = Typ. 70° |
Vertical | Revision ≥ H3: Direction U / Direction D = Typ. 50° Revision < H3: Direction U / Direction D = Typ. 60° |
Backlight | |
Type | LED |
Brightness | Typ. 500 cd/m² |
Half-brightness time | 50,000 h |
Touch screen | |
Type | AMT |
Technology | Analog resistive |
Controller | B&R, serial, 12-bit |
Transmittance | 80% ±3% |
Screen rotation | Yes, using Visual Components |
Interface IF1 | |
Fieldbus | POWERLINK V2 managing or controlled node |
Type | Type 4 |
Variant | 1x RJ45 shielded |
Line length | Max. 100 m between 2 nodes (segment length) |
Max. transfer rate | 100 Mbit/s |
Transfer | |
Physical layer | 100BASE-TX |
Half-duplex | Yes |
Full-duplex | POWERLINK mode: No / Ethernet mode: Yes |
Autonegotiation | Yes |
Auto-MDI/MDIX | Yes |
Interface IF2 | |
Type | Ethernet |
Variant | 1x RJ45 shielded |
Line length | Max. 100 m between 2 nodes (segment length) |
Max. transfer rate | 10/100 Mbit/s |
Transfer | |
Physical layer | 10BASE-T/100BASE-TX |
Half-duplex | Yes |
Full-duplex | Yes |
Autonegotiation | Yes |
Auto-MDI/MDIX | Yes |
Interface IF3 | |
Type | USB 2.0 |
Variant | Type A |
Current-carrying capacity | 0.49 A |
Interface IF4 | |
Type | USB 2.0 |
Variant | Type A |
Current-carrying capacity | ≥Rev. E0: 0.20 A <Rev. E0: 0.10 A |
Interface IF5 | |
Fieldbus | X2X Link master |
Interface IF6 | |
Type | CAN bus |
Variant | 3 pins of the 6-pin multipoint connector |
Max. distance | 1000 m |
Max. transfer rate | |
Bus length ≤25 m | 1 Mbit/s |
Bus length ≤60 m | 500 kbit/s |
Bus length ≤200 m | 250 kbit/s |
Bus length ≤1000 m | 50 kbit/s |
Terminating resistor | Hardware revisions ≥G0: Integrated, can be switched on using software Hardware revision <G0: Must be wired externally |
Interface IF8 | |
Type | RS232 |
Variant | 3 pins of the 6-pin multipoint connector |
Max. distance | 900 m |
Transfer rate | Max. 115.2 kbit/s |
Nominal voltage | 24 VDC -15% / +20% |
Max. power consumption | 15 W |
Reverse polarity protection | Yes |
Electrical isolation | IF1, IF2 and IF5 isolated from each other, from other interfaces and from the base device |
Consúltenos reparaciones, servicio tecnico.
Mas información?
Power Panel C70 User’s manual
Weight | 0,7 kg |
---|---|
Dimensions | 19 × 19,7 × 14 cm |